HDMI/ DVI Extender

  • Creative HDMIEx 1020.A is a series of DVI / HDMI extenders designed to equalize and retime DVI / HDMI signal paths in order to provide a low jitter version of the original clock and data signal at its output to drive a distant HDMI capable display.
  • Signal Support - HDMITx 1020.A supports all the HDMI standards and features through 1.3. These expanded features include support for Deep Color and 1080p50/60 HD resolutions with embedded 8-channel digital audio.
  • HDMIEx1020.A can extend the useable length of HDMI / DVI cables up to 35 meters by equalizing the input and regenerating the HDMI signal at the output before the signal is sent to the display.

USB to CAT5 Extender

Creative CE USB 4103.C series of USB to CAT5 Extenders, Extend USB Signal > 50mtrs using a single common
UTP cable from the location of your computer or any other USB Device. This device is an extension cable between
USB device and host (computer) with embedded into connector “intelligent” integrated circuits on both sides of the cable.
These units are designed to work in pairs using a USB-to-CAT5 Transmitter (Tx) and a CAT5-to-USB Receiver
(Rx) to extend the USB signal.

CAT5 Tx - DA 1:4

Creative expands its line of audio/video / RS232 / IR-over-CAT5 cable products with the introduction of a high-performance CAT5 Distribution Amplifier, Model CETx DA124. The DA124 is used to fan out to multiple locations the output from Creative CAT5 Transmitter Module, allowing the same signals to be sent to upto four different Creative CAT5 (Rx) Receivers. The RS232 or IR serial communication between the Tx and the four Rx’s provides the same commands to all locations.

Features

  • Built-in lightning, power surge and transient protection.
  • Distributes VGA, Stereo Audio, and RS232 or IR serial communications.
  • Maximum RGB Resolution 2048 x 1536.
  • One Bidirectional RS-232 or IR-link control path, three Tx only control path
  • Uses easy to install, inexpensive CAT-5/5e/6/7/8.
  • Selector Switch: For Analog adjustment. range up to 1000 Feet
  • Data return selector— Selects which of the remote locations is able to send data back to the Tx unit.
  • High ground loop immunity. For Better NOICE Reduction.
  • Unit offers real—world Protection with Automatic Reset Fuses and built-in Power surge and transit Protection. This Unit also includes an isolated Power Supply for Protection against Ground Loops.

VGA to CAT5 Converter

Creative introduces a high-performance CAT5 Tx1003 Transmitter and Rx1003 Receiver to be used in pairs for the extension of VGA, Stereo Audio, and IR or RS-232 data. The RGB-to-CAT5 Converter (Tx1003) converts the RGB video, Stereo Audio, and IR or RS-232 to signal levels that can be transmitted up to 300M to the remotely installed CAT5-to-Display Device (Rx1003) using AT5/CAT5e/CAT6/7/8 UTP cable.

Timing to correct the delay differences between the pairs : These are very cost effective, third-generation products which utilize application specific linear devices to provide the fastest video rise times and pixel cycling possible over UTP cable.

Signal Loops and Dual Outputs, : The Tx1003 features loop thru VGA and stereo audio inputs, while the Rx1003 provides dual VGA and stereo audio outputs. Eliminating need of Distribution amplifiers in many system configurations

Features

  • Adaptable Gain/EQ using a single control
  • Bidirectional RS-232 or IR-link control paths
  • Sync polarity preservation or conversion
  • Line Level Audio inputs / outputs (-10dBv)
  • Communication LEDs for reporting RS-232 or IR-link activity
  • Duplex RS-232/IR + VGA + stereo audio over a single CAT5
  • Dual Audio and Video outputs
  • Uses easy to install, inexpensive CAT-5/5e/6/7/8
  • Cable EQ / Gain range up to 1000 Feet
  • Maximum RGB Resolution 2048 x 1536; Distance 1000 Feet
  • Sends high-resolution UXGA, Stereo Audio and Compatible with Line Level Stereo Audio Signals.
  • High ground loop immunity. For Better NOICE Reduction
  • Built-in lightning, power surge and transient protection. Designated trimmer in the remote unit to compensate for cable length.
  • Supports RS232 and IR

4 Way PC Distribution Amplifier - Audio LR PCDA-1004

Creative’s 4 way PC Distribution Amplifier Model Audio LR PCDA-1004 is a one RGB Video –input and four RGB Video-output PC Stereo Audio RGB Video distribution amplifier specifically designed for driving multiple drops and long cables runs. This Device works with any video resolution as it distributes the RGBHV from any video graphics source to four separate display devices. With 350 MHz of video bandwidth, and using standard VGA cable, the LR PCDA-1004 is capable of maintaining signal clarity with up to 150mtr. of cable. Each output
is a high current driver necessary to maintain the original signal quality over long cable runs. In fact, the LR PCDA-1004 guarantees the proper
driver impedance for all outputs which helps to reduce interference and noise under all conditions. LR PCDA-1004 is compatible with any LCD, Plasma or DLP projectors, as well as any high-end CRT monitor or Video Wall.

Key Features

  • 350 MHz RGB video bandwidth
  • Resolution independent
  • Bi-color LED for sync presence diagnostic
  • Hi-current outputs for long cable runs
  • Compatible with any type of display device Transparent signal quality
  • Rigid metal enclosure
  • Supports any resolution or frame rate
  • Internal 240VAC, 50/60 Hz, Power Supply
  • LR PCDA-1004 guarantees the proper driver impedance
Applications
  • Institutional Organisations
  • Computer Centre
  • Video Walls
  • Auditoriums
  • Home Theatre
  • Rental Applications
  • Board Room
  • Conference Halls
  • Airport / Railway Stations

PC Distribution Amplifier - PCDA-1002

Creative’s PC Distribution Amplifier Model PCDA-1002 is a one RGB Video – input and Two RGB Video-output distribution amplifier specifically designed for driving multiple drops and long cables runs. This Device works with any video resolution as it distributes the RGBHV from any video graphics source to Two separate display devices. With 350 MHz of video bandwidth, and using standard VGA cable, the PCDA-1002 is capable of maintaining signal clarity with up to 150mtr. of cable. Each output is a high current driver necessary to maintain the original signal quality over long cable runs. In fact, the PCDA-1002 guarantees the proper driver impedance for all outputs which helps to reduce interference and noise under all conditions. PCDA-1002 is compatible with any LCD, Plasma or DLP projectors, as well as any high-end CRT monitor or Video Wall.

Key Features

  • Resolution independent
  • Hi-current outputs for long cable runs
  • Compatible with any type of display device Transparent signal quality
  • Rigid metal enclosure
  • Supports any resolution or frame rate
  • Internal 240VAC, 50/60Hz, Power Supply
  • PCDA-1002 guarantees the proper driver impedance.
  • 350 MHz RGB video bandwidth
Applications
  • Institutional Organisations
  • Computer Centre
  • Video Walls
  • Auditoriums
  • Home Theatre
  • Rental Applications
  • Board Room
  • Conference Halls
  • Airport / Railway Stations

4x1 Audio follow Video Switcher

Creative introduces a high performance 4x1 audio follow video switcher for computer graphic video signals up to QXGA resolutions. The PC4100AFV allows ultiple computers to be switched to one display and audio monitor. The PC4100AFV is compatible with RGB video levels and IHF level unbalanced stereo audio sources.

The PC4100AFV can be controlled via front panel momentary pushbuttons or remotely using AMX / Crestron compatible commands via the RS-232 serial  port. The PC4100AFV also includes a sequence generator with a variable rate control. Using sequence allows the switcher to switch between the inputs sources at a preset rate. There is also a “Skip Mode” available so that when the switcher is in the sequence mode it will automatically skip inputs missing sync. When the PC4100AFV is in the sequence mode the audio sources are muted.

Three modes available for VGA Switch

  • Manual mode, client selects the video by push button
  • Sequence mode, unit sequentially switches to each input whether there is input or not.
  • Sequence with Skip, unit sequentially switches to each input if it is there (skips the missing ones)

The potentiometer on Front Panel adjusts the sequence speed. This potentiometer allows speed changes from fast to up to about 15 second between switching.

Signal Capabilities

  • PC4100AFV also scan to first input available and stop.PC4100AFV is compatible with any PC/Laptop/Work Station supporting up to QXGA Resolution and line output level stereo audio.
  • PC4100AFV can work with any sync levels and any sync polarity. The output sync will be of proper level and polarity regardless of input sync levels or polarity.

High Resolution Cross Point

Auto detection of sync presence is also provided for output connectivity. PC4100AFV uses very-high-bandwidth(350Mhz) RGB cross points to Provide transparent image clarity at virtually any resolution.

Advanced Features

  • Auto Sequencing
  • Auto Sync Detection (this will detect Sync on Out Put Stage)
  • RS232 Compatibility
  • Swap Feature (Adjustable Time Speeds)
  • Audio Muting in Swap Mode
  • Audio Level Control
  • LED indication for active source

SI-4004 - Relay Box

SI-4004 is a Relay Box Designed to control movement of Projection Screen / Projector Lift / Drapes. All these functions are Timer Controlled. This can be configured to any RF Control Processors. This Device can also Switch On / Off Complete Equipment Rack Power. While doing integration of Audio Video Equipments / Projection Screen / Projector Lift and Drapes, controlled with Touch Panel (like AMX and Crestron or any other high end RF Remote Control System) in Board Rooms and Auditoriums we require some interface to control movement of Projection Screen, Lift and Drapes which is connected with
Processor of touch panel. Or even Complete Rack in which all these equipments are mounted. Introducing you here with Timer Controlled Dual Function Screen Interface Model SI 4004. Which can control movement of Motorized Projection Screen, Projector Lift, Drapes and even complete Equipment Rack Power.

  • Ideal to control motorized Projection Screen / Projector Lift / Drapes and Equipment Rack (AC 220 V operated).
  • Timer Controlled ACTION : Cut off supply to Screen / Lift and Drapes automatically after 1.5 minutes.
  • Can be used to “ON” “OFF” Complete rack in.
  • Manually Controlled: Can be used to control movement of Screen / Lift and drapes manually (without touch panel) with three individual switch provided on front panel.
  • Blinking LED provided on front Panel to show the active function
  • Institutional Organizations
  • Computer Center
  • Auditoriums
  • Board Rooms; Conference Halls
  • Air Ports; Railway Stations

Projection Screen Interface - SI-2002

Projection Screen Interface, Model SI - 2002 Device is with Electronic Timer controlled. This can Control Movement of Projection Screen and is Compatible with Any Type of RF Remote systems Like (AMX or Crestron) You can also Switch On / Off Mains Power Supply to Equipment Rack. In case of Failure to any Device (Processor or Screen Interface), Provision is given to Control Screen movement manually.

Key Features

  • Ideal to control motorized Projection Screen. (AC 220 V operated).
  • Timer Controlled Action : Cut off supply to Screen automatically after 1.5 minutes.
  • Can be used to “ON” “OFF” CompleteEquipment Rack Power Supply.
  • Manual Control: Can be used to control Up and Down movement of Screen manually with switch provided on front panel.
  • Blinking LED provided on front Panel to show the active function

Applications

  • Institutional Organizations
  • Auditoriums
  • Home Theaters
  • Board Rooms
  • Conference Halls

AVDA 1004

AVDA 1004 is a one input, four-output Audio Video distribution amplifier with stereo audio on RCA connectors. With >200 MHz video bandwidth, this DA features Unity gain. For compensation of signal level loss that occurs over long cable runs. Individual buffers and amplifiers ensure that all output channels are equivalent in terms of signal strength and integrity to the original input signal. AVDA 1004 is designed to provide signal distribution and amplification for the professional Audio Video market - to meet specific system requirements for distributing multiple outputs from a single input. It provides increased system flexibility and performance. AVDA 1004 is compatible with NTSC, PAL, and SECAM video signals, allows cable runs of 1,000 feet (300 meters) or more, depending on the quality of the cable used.

Applications

  • Institutional Organizations
  • Computer Center
  • Auditoriums
  • Board Rooms; Conference Halls
  • Air Ports; Railway Stations
  • Institutional Organizations
  • Computer Center (With VGA to PAL converter)
  • Video Walls
  • Rental Applications

AVDA 1002

Creative’s AVDA 1002 is a one input, Two-output Audio Video distribution amplifier with stereo audio on RCA connectors. With >200 MHz video bandwidth, this DA features Unity gain. For compensation of signal level loss that occurs over long cable runs. Individual buffers and amplifiers ensure that all output channels are equivalent in terms of signal strength and integrity to the original input signal. AVDA 1002 is designed to provide signal distribution and amplification for the professional Audio Video market - to meet specific system requirements for distributing multiple outputs from a single input. It provides increased system flexibility and performance.

Key Features

  • AVDA 1002 is compatible with NTSC, SECAM, PAL video signals.
  • Allows cable run of 1,000 feet (300 meters) or more, depending on the quality of the cable used.


Applications

  • Air Ports; Railway Stations
  • Institutional Organizations
  • Computer Center (WithVGA to PAL converter)
  • Video Walls
  • Auditoriums
  • Rental Applications
  • Board Rooms; Conference Halls
  • Air Ports; Railway Stations and Security Purposes


Video Interface - VI-1002

VI 1002 is a analog computer-video interface with a female 15-pin HD input connector and a 15-pin HD buffered local monitor output. The VI 1002 has a 15-150 kHz scanning range, 350 MHz RGB video bandwidth, and is compatible with nearly every computer / Work Stations and video signal type, including VGA – UXGA. The VI 1002 also features Auto ID bit Selection, ensuring that computers requiring local monitors to operate will do so in the event that one is not attached. For PCs, the VI 1002 connectivity is on 15-pin HD male to male cable. VI—1002 is compatible for both RGBHV (5 in BNC female connector) and Composite Sync (RGBH) which can be switched manually with a sleek toggle Switch On front PANEL. This also features advanced sync processing circuitry for enhanced signal coming from Computer / Laptop and WORK STATIONS. VI 1002 can also be connected to Scalars (video to VGA converters) VI—1002 can sense the verity of sync levels like RGBHV, RGBs or RGsB automatically which doesn’t need to be selected by any DIP switch combination. In addition to, no DIP switch combination is required when there is change of resolution from 640X480 onwards. VI 1002 adjusts itself to active resolution. Auto ID bit selection is also provided for buffered and main output connectivity.

Key Features

  • 350 MHz RGB video bandwidth
  • Resolution independent
  • Hi-current outputs for long cable runs
  • Compatible with any type of display device Transparent signal quality
  • Rigid metal enclosure
  • Supports any resolution or frame rate
  • Internal 240VAC, 50/60 Hz, Power Supply
  • VI—1002 guarantees the proper driver impedance.

Applications

  • Institutional Organisations
  • Computer Center
  • Video Walls
  • Auditoriums
  • Home Theater
  • Rental Applications
  • Board Room
  • Conference Halls
  • Airport / Railway Stations

Feedback LOGIC Controller - FLC 8001

Creative’s new product to aid in successful video conferencing (VC). The Feedback LOGIC Controller, Model FLC8001, is a unique device used to control audio routing and camera selection. The purpose of the FLC8001 is to eliminate audio feedback when using Automatic Mixers in VC applications. The FLC8001 can be used with any high-end manual, voice activated, or RF controlled automation device. Imagine: The moment a participant’s microphone is selected: (1) the desktop or ceiling speaker associated with this participant must be muted to avoid audio feedback; and, (2) the programmed camera position must be recalled so the camera is directed toward the participant. This is a popular VC set up known as “LOOK AT ME”. The FLC8001 accepts control logic from the automat ion device and mutes the participant ’s speaker, then signals the camera controller to move the pan and tilt head putting the participant in the field of view.

Key Features

  • Three way LOGIC Selection – Manually, RF Touch Panels and Voice Level
  • Controls VC Camera
  • Mutes Speaker(s) connected with selected Mic.
  • Works on LOGIC Generated from Automatic Mixer
  • LED Indication for Selected Speaker
Applications
  • Board Rooms; Conference Halls
  • Institutional Organizations
  • Computer Center
  • Auditoriums